About the SynDeck® NuFlex Epoxy SS1286
SynDeck™ NuFlex Epoxy (SS1286) is a two component, 100% solids, high build self-levelling colored epoxy that meets IMO FTP Code 2010, MIL-PRF 32584, and Def. Stan. 07-247 requirements. It has excellent chemical and moisture resistance and is very low odor. This product is a resilient decking material and water barrier that is formulated to be applied directly to metal and other properly prepared substrates or other SynDeck™ leveling underlayments for military and commercial marine specification applications. It is typically a trowel-applied product, but can also be brushed and rolled. NuFlex Epoxy has good flow and leveling properties, and decorative flakes can be applied into the wet NuFlex Epoxy to create a unique look. This product is not a final finish and will require a SynDeck™ sealer.
Features
- Meets parts 2 and 5 of annex 1 of the IMO FTP Code 2010 for Floor Covering
- Meets and exceeds ANSI A118.10 requirements
- Qualified to MIL-PRF-32584 as part of various systems
- Meets NAG Defence Standard 07-247 as part of various SynDeck™ systems
Variants
See variants| Arctic Ice Blue: | 34.37lbs (15.59kg) | 3.19Gal (12.07L) |
| Tan: | 36.58lbs (16.59kg) | 3.19Gal (12.07L) |
| Cadet Silver: | 37.72lbs (17.11kg) | 3.42Gal (12.95L) |
| Deep Sea Blue: | 31.17lbs (14.14kg) | 3.05Gal (11.55L) |
| Pewter Gray: | 37.29lbs (16.91kg) | 3.39Gal (12.83L) |
| Scarlett Red: | 36.59lbs (16.61kg) | 3.51Gal (13.29L) |
| Arctic Ice Blue: | 6.18lbs (2.80kg) | 0.57Gal (2.16L) |
| Tan: | 6.59lbs (3.00kg) | 0.60Gal (2.27L) |
| Cadet Silver: | 6.79lbs (3.08kg) | 0.62Gal (2.35L) |
| Deep Sea Blue: | 5.97lbs (2.71kg) | 0.56Gal (2.12L) |
| Pewter Gray: | 6.71lbs (3.04kg) | 0.61Gal (2.31L) |
| Scarlett Red: | 6.59lbs (2.99kg) | 0.63Gal (2.39L) |
Benefits
- 100% solids, 0g/ L VOC
- High build, self-levelling
- Flexible & impact resistant
Applications
SynDeck™ NuFlex Epoxy SS1286 series can be applied to properly prepared metal substrate decks or the SynDeck™ RediDeck System as a resilient coat where fairing and leveling is required. It is a one-step process that does not require a bond coat or waterproof membrane. This product is self-leveling and is an especially favored epoxy for high build applications in wet spaces.
- Surface PreparationDirect to metal: All visible oil, grease, sludge and any other contaminants must be removed prior to mixing and application. SSPC SP11 / ISO 8501-1 ST3 (power tool) at minimum, SSPC-SP10 / ISO 8501 - 1 SA2.5 (blasting preferable). Surface m ust be clean, dry, corrosion free, and have a 1-3 mil (25-75 micron) surface profile. Existing coatings and/ or after re-coat window : Light abrasion to achieve a 1-3 mil (25-75 micron) surface profile. Surface must be solvent cleaned, dry, and free of contaminants.
- MixingMix NuFlex Epoxy Part A Resin SA1286 until a homogenous mixture is obtained. Next, pour Part B Hardener SB1286 into Part A Resin component and mix slowly (500-1000 rpm) using a mechanical jiffy-type mixer for 1-2 minutes. Scrape the sides of the container and mechanically mix for an additional 1 minute. It is very important to achieve a proper mechanical mix. In the mixing process, take care not to introduce excessive air into the material in order to achieve a completely homogenous mixture.
- ApplicationTrowell: For application to coving and bulkheads, use a high quality roller or stiff bristle brush. To build sufficient material, use a top-quality flat or notched trowel depending on desired material thickness. A notched trowel will aid in air release and provide a uniform application thickness. SynDeck™ NuFlex Epoxy may also be applied with a brush or roller in a low-build application. Use of a spiked or porcupine roller after application is recommended to additionally help release air. Application note: Pot life is dependent on the size of mixed material. Do not mix more material than can be applied within 30 minutes
- Clean UpClean hands and skin with warm water and mild soap. Clean tools and equipment with MEK, denatured alcohol, or acetone.
Related products
Why choose ERS Marine for your SynDeck® product installations?
ERS Marine has been a trusted partner of SynDeck® for over 10 years. Our team of experts are trained and certified to install SynDeck® products to the highest standards. We offer a range of services to ensure your project is completed on time and on budget.
Get a quote