Sikafloor Marine Litosilo X - 20kg
Floating floor for interior decks suitable for A 60 divisions and acoustic solutions.
About the Sika Sikafloor Marine Litosilo X - 20kg
Sikafloor® Marine Litosilo X is a 1-component medium weight high strengths levelling mortar based on polymer modified cement with excellent flame resistance.Sikafloor® Marine Litosilo X is tested according to FTP Code system and approved according to the IMO Marine Equipment Directives.
Features
- Approved as A-60 class division with Isover and Rockwool
- Fast setting
- Magnesium chloride free
- Non combustible
- Can be pumped (fast setting needs to be considered)
- One component, ready to mix
Benefits
- Approved as A-60 class division with Isover and Rockwool
- Fast setting
- Magnesium chloride free
- Non combustible
- Can be pumped (fast setting needs to be considered)
- One component, ready to mix
Applications
Sikafloor® Marine Litosilo X is applied on interior decks, as primary deck covering or as sound reducing floating floor prior to the application of deck finishing materials such as: carpets, tiles, parquet, rubber and vinyl.There are various combinations with Sikafloor® Marine Litosilo X to achieve an A 60 division and combined with insulation and a Sika visco-elastic system it can in addition be used to damp structure borne noise.This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Get the Sikafloor Marine Litosilo X - 20kg installed by ERS Marine
- Surface PreparationFor levelling applications, the surface has to be clean, free from dust, grease, oils and other substances, which may impair adhesion. Rust has to be removed with a steel brush or other appropriate means, followed by vacuum cleaning.The surface has to be primed with Sikafloor® Marine Primer C using a long hair roller. After drying of the Sikafloor® Marine Primer C, Sikafloor® Marine Litosilo X may be applied. Sikafloor® Marine Litosilo X applications on aluminum or zinc rich shop primer coated decks, require a tie coat of SikaCor® ZP Primer or another suitable tie coat prior the priming step with Sikafloor® Marine Primer C.For floating floors, the mineral wool has to be sound (not damaged), clean, dry free from grease, oils and other substances. It’s a must to use re-enforcement such as wire mesh or similar for the whole area and extra re-enforcement (e.g. steel plates) where ever a higher load is expected such as in both sides of doors areas, staircases, etc.Further details for floating floors consult the Application Manual of Sikafloor® Marine Litosilo X and its approved combinations.Consider that prior applications of vinyl and carpet coverings, a thin self levelling mortar such as Sikafloor® Marine 100 has to be applied to obtain an even floor. For wet areas the surface has to be treated with a water resistant membrane (e.g. Sikafloor® Marine Elastic).
- ApplicationApply the mortar with a steel board or a straight edge.Sikafloor® Marine Litosilo X has to be applied within 30 minutes after mixing. At temperatures above 30 °C the open time will be reduced to 10 minutes or less.For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
- CuringAfter application, the finished areas have to be protected against direct heat (e.g. cutting or welding from beneath), sunlight and draught during the curing process for at least 12 hours. Before Sikafloor® Marine Litosilo X is covered with dense materials such as vinyl, epoxy or polyurethane coatings, etc., ensure that the remaining moisture level is below 4%. Test procedure to determine the dryness (according ASTM D 4263): put a PE-plastic foil 1 m x 1 m on the surface of the applied mortar floor, tape the perimeter and leave for one day. The curing is complete if there is no water condensation on the foil or a visible color difference between covered and uncovered surface.
- RemovalExcess material can best be removed before curing with a trowel wipe or water.Fresh Sikafloor® Marine Litosilo X may be removed from tools and equipment with water. Once cured, the material can only be removed mechanically.Exposed hands and skin shall be washed immediately with water. Use a suitable skin protection hand cream.
Related products
Sikafloor Marine Primer C - 10kg
Pigmented, water-based primer for interior shop primed steel and mortar applications
PrimersSikafloor Marine Litosilo N - 20kg
Floating floor for interior decks suitable for A 60 divisions and acoustic solutions
Interior Deck CoveringsFloating FloorsSound Reducing Floating FloorsSikafloor Marine 190 - 25kg
Self-levelling primary deck covering for interior decks
Interior Deck Coverings
Why choose ERS Marine for your Sika product installations?
ERS Marine has been a trusted partner of Sika for over 10 years. Our team of experts are trained and certified to install Sika products to the highest standards. We offer a range of services to ensure your project is completed on time and on budget.
Get a quote