Sika logo

Sikafloor Marine 190 - 25kg

Self-levelling primary deck covering for interior decks.

Buy now Read the data sheet
Product image
Products / Sika / Sikafloor Marine 190 - 25kg

About the Sika Sikafloor Marine 190 - 25kg

Sikafloor® Marine-190 is a 1-component self-levelling mortar based on polymer modified cement.Sikafloor® Marine-190 is tested according to FTP Code system and approved according to IMO Marine Equipment Directives.

CategoriesInterior Deck Coverings

Features

  • Fast setting
  • Can be pumped
  • Non combustible
  • One component, ready to mix
  • Easily applicable

Benefits

  • Fast setting
  • Can be pumped
  • Non combustible
  • One component, ready to mix
  • Easily applicable

Applications

Sikafloor® Marine-190 is applied on interior decks, to level the surface prior to the application of deck finishing materials such as: carpets, tiles, parquet, rubber and vinyl. It is suitable for application in dry and wet accommodation areas.This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.

Picture of the Sikafloor Marine 190 - 25kg product

Get the Sikafloor Marine 190 - 25kg installed by ERS Marine

Get a quote
  • Surface PreparationFor levelling applications, the surface has to be clean, free from dust, grease, oils and other substances, which may impair adhesion. Rust has to be removed with a steel brush or other appropriate means, followed by vacuum cleaning.The surface has to be primed with Sikafloor® Marine Primer C using a long hair roller. After drying of the Sikafloor® Marine Primer C, Sikafloor® Marine-190 may be applied. For wet areas the surface has to be treated with a water resistant membrane (e.g. Sikafloor® Marine Elastic). Sikafloor® Marine-190 applications on aluminum or zinc rich shop primer coated decks, require a tie coat of SikaCor® ZP Primer or another suitable tie coat prior the priming step with Sikafloor® Marine Primer C.
  • ApplicationApply the mortar with a steel board or a straight edge. Sikafloor® Marine-190 can also be applied by pinrake.Sikafloor® Marine-190 has to be applied within 20 minutes after mixing. At temperatures above 30 °C the open time will be reduced to 10 minutes or less.For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
  • CuringAfter application, the finished areas have to be protected against direct heat (e.g. cutting or welding from beneath), sunlight and draught during the curing process for at least 12 hours.Before Sikafloor® Marine-190 is covered with dense materials such as vinyl, epoxy or polyurethane coatings, etc., ensure that the remaining moisture level is below 4%. Test procedure to determine the dryness (according ASTM D 4263): put a PE-plastic foil 1 m x 1 m on the surface of the applied mortar floor, tape the perimeter and leave for one day. The curing is complete if there is no water condensation on the foil or a visible color difference between covered and uncovered surface.
  • RemovalExcess material can best be removed before curing with a trowel wipe or water.Fresh Sikafloor® Marine-190 may be removed from tools and equipment with water. Once cured, the material can only be removed mechanically.Exposed hands and skin shall be washed immediately with water. Use a suitable skin protection hand cream.
  • Application LimitsFor applications on slooping surfaces > 1 % contact the Technical Department of Sika Industry.

Related products

ERS Marine

Why choose ERS Marine for your Sika product installations?

ERS Marine has been a trusted partner of Sika for over 10 years. Our team of experts are trained and certified to install Sika products to the highest standards. We offer a range of services to ensure your project is completed on time and on budget.

Get a quote